Difference between revisions of "Realistic Fire Simulation"

From Tuxamito
Jump to: navigation, search
(Building)
(Final Result)
 
(2 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
In this page is described how to create a realistic flickering fire effect with LEDs and an Arduino board. In this case I used a [[Digispark]] due to its small size.  
 
In this page is described how to create a realistic flickering fire effect with LEDs and an Arduino board. In this case I used a [[Digispark]] due to its small size.  
  
The intention is to give some light to a small clay decoration house, one of those prepared for lighting a small candle inside and evaporate water with essence. Instead of using a candle I put a simple battery with some LEDs inside but it looked too boring so I tried to imitate the movement of a candle inside it. Here it is described the design and process followed.
+
The intention is to give some light to a small clay decoration house, one of those prepared for lighting a small candle inside and evaporate water with essence. Instead of using a candle I put a battery with some LEDs inside but it looked too boring so I tried to imitate the movement of a candle inside it. Here it is described the design and process followed.
  
 +
The concept is similar, with red and yellow LEDs illuminating inside the clay house, but with a flickering effect imitating a candle. The flickering effect can be created with an Arduino handling the LEDs power. The power for each LED is determined randomly with an update time that is also random (see the code later in this page).
  
 
== Component Schematics ==
 
== Component Schematics ==
The three LEDs (two reds and one yellow - I guess one red and two yellows would also look nice) are connected to the PWM ports of the arduino (Digispark, which has exactly 3 PwM pins).
+
The three LEDs (two reds and one yellow - I guess one red and two yellows would also look nice) are connected to the PWM ports of the arduino (Digispark, which has exactly 3 PwM pins). The LEDs are connected logically inverted (the LED is powered when the pin is at LOW status and it is off when the pin is at HIGH status) because it is safer for most integrated circuits to drain power than to provide it (although for this microcontroller we are in the safe range).
  
 
[[File:Fire_led_schema1.png]]
 
[[File:Fire_led_schema1.png]]
Line 17: Line 18:
  
 
In the next picture the connections for the LEDs in pins 0 and 4 have been soldered. Each pin has two 470 ohm resistors in parallel that make a total of 235 ohm (I did not have 220 ohm or similar). As the system is powered by 4.8v that makes a maximum of a bit more of 20 mA per LED, which should be bright enough and safe for the microcontroller. Visit the next section to have a look at code running in the board.
 
In the next picture the connections for the LEDs in pins 0 and 4 have been soldered. Each pin has two 470 ohm resistors in parallel that make a total of 235 ohm (I did not have 220 ohm or similar). As the system is powered by 4.8v that makes a maximum of a bit more of 20 mA per LED, which should be bright enough and safe for the microcontroller. Visit the next section to have a look at code running in the board.
 +
 
[[File:firesimled01.jpg]]
 
[[File:firesimled01.jpg]]
 +
  
 
The next picture shows the system already assembled, the two conventional LEDs plus the one included in the board, with a 4x AAA 1.2v battery pack (giving a total of 4.8v). The battery pack has to be connected to the 5v and GND connector of the Digispark board (4.8v is enough). The Digispark board has a power on red LED that has been removed with a sharp knife because the continuous red light was spoiling the fire effect.
 
The next picture shows the system already assembled, the two conventional LEDs plus the one included in the board, with a 4x AAA 1.2v battery pack (giving a total of 4.8v). The battery pack has to be connected to the 5v and GND connector of the Digispark board (4.8v is enough). The Digispark board has a power on red LED that has been removed with a sharp knife because the continuous red light was spoiling the fire effect.
 +
 
[[File:firesimled02.jpg]]
 
[[File:firesimled02.jpg]]
 +
  
 
This picture shows the powered on system inside the bottom of the clay house, with the three lights already flickering.
 
This picture shows the powered on system inside the bottom of the clay house, with the three lights already flickering.
 +
 
[[File:firesimled03.jpg]]
 
[[File:firesimled03.jpg]]
 +
 +
The average power consumption is around 45-50mA with peaks that can be a bit higher (due to the random LED powers), which should power the system for about 20 hours with 1000 mAh batteries, or 10 hours with chaper 500 mAh ones, which is enough for our purposes.
  
 
== Code ==
 
== Code ==
Line 84: Line 92:
  
 
== Final Result ==
 
== Final Result ==
 +
 +
I have to say that I am very satisfied with the result, keep in mind that in real is nicer than in the recorded video:
  
 
{{#evt:
 
{{#evt:

Latest revision as of 10:36, 5 January 2016

In this page is described how to create a realistic flickering fire effect with LEDs and an Arduino board. In this case I used a Digispark due to its small size.

The intention is to give some light to a small clay decoration house, one of those prepared for lighting a small candle inside and evaporate water with essence. Instead of using a candle I put a battery with some LEDs inside but it looked too boring so I tried to imitate the movement of a candle inside it. Here it is described the design and process followed.

The concept is similar, with red and yellow LEDs illuminating inside the clay house, but with a flickering effect imitating a candle. The flickering effect can be created with an Arduino handling the LEDs power. The power for each LED is determined randomly with an update time that is also random (see the code later in this page).

Component Schematics

The three LEDs (two reds and one yellow - I guess one red and two yellows would also look nice) are connected to the PWM ports of the arduino (Digispark, which has exactly 3 PwM pins). The LEDs are connected logically inverted (the LED is powered when the pin is at LOW status and it is off when the pin is at HIGH status) because it is safer for most integrated circuits to drain power than to provide it (although for this microcontroller we are in the safe range).

Fire led schema1.png

The pin P1 of the Digispark board already has red LED attached to it, so there is no need to add a new one, or to remove the current one. For this reason the new schematics is:

Fire led schema2.png


Building

In the next picture the connections for the LEDs in pins 0 and 4 have been soldered. Each pin has two 470 ohm resistors in parallel that make a total of 235 ohm (I did not have 220 ohm or similar). As the system is powered by 4.8v that makes a maximum of a bit more of 20 mA per LED, which should be bright enough and safe for the microcontroller. Visit the next section to have a look at code running in the board.

Firesimled01.jpg


The next picture shows the system already assembled, the two conventional LEDs plus the one included in the board, with a 4x AAA 1.2v battery pack (giving a total of 4.8v). The battery pack has to be connected to the 5v and GND connector of the Digispark board (4.8v is enough). The Digispark board has a power on red LED that has been removed with a sharp knife because the continuous red light was spoiling the fire effect.

Firesimled02.jpg


This picture shows the powered on system inside the bottom of the clay house, with the three lights already flickering.

Firesimled03.jpg

The average power consumption is around 45-50mA with peaks that can be a bit higher (due to the random LED powers), which should power the system for about 20 hours with 1000 mAh batteries, or 10 hours with chaper 500 mAh ones, which is enough for our purposes.

Code

For schematic 1, with all LEDs logically inverted:

int p1 = 0; // Set the 3 pins with PWM
int p2 = 1;
int p3 = 4;

void setup() {
  pinMode(p1, OUTPUT); // Set the pins as output
  pinMode(p2, OUTPUT);
  pinMode(p3, OUTPUT);
}

void loop() {
  int v1, v2, v3;

  v1 = random(155) + 100; // Calculate the new light
  v2 = random(155) + 100; // intensity values for each LED
  v3 = random(155) + 100;

  analogWrite(p1, 255 - v1); // Apply the light intensity
  analogWrite(p2, 255 - v2); // to each LED
  analogWrite(p3, 255 - v3);

  delay(20 + random(80)); // Wait some random time for next udpate
}


For schematic 2 (reusing the LED attached to Pin 1, which is not "logically inverted"):

int p1 = 0; // Set the 3 pins with PWM
int p2 = 1;
int p3 = 4;

void setup() {
  pinMode(p1, OUTPUT); // Set the pins as output
  pinMode(p2, OUTPUT);
  pinMode(p3, OUTPUT);
}

void loop() {
  int v1, v2, v3;

  v1 = random(155) + 100; // Calculate the new light
  v2 = random(155) + 100; // intensity values for each LED
  v3 = random(155) + 100;

  analogWrite(p1, 255 - v1); // Apply the light intensity to each  LED
  analogWrite(p2, v2);       // This LED is not "logically inverted"
  analogWrite(p3, 255 - v3);

  delay(20 + random(80)); // Wait some random time for next udpate
}


Final Result

I have to say that I am very satisfied with the result, keep in mind that in real is nicer than in the recorded video: