Difference between revisions of "Digispark"

From Tuxamito
Jump to: navigation, search
(Created page with "The Digispark is an Attiny85 based microcontroller development board similar to the Arduino line, perfect for when an Arduino is too big. === Specification === * Attiny85 * P...")
 
Line 1: Line 1:
The Digispark is an Attiny85 based microcontroller development board similar to the Arduino line, perfect for when an Arduino is too big.
+
The Digispark is an Attiny85 based microcontroller development board similar to the Arduino line, perfect for when an Arduino is too big. The
  
 
=== Specification ===
 
=== Specification ===
Line 12: Line 12:
 
* ADC on 4 pins
 
* ADC on 4 pins
 
* Power LED and Test/Status LED
 
* Power LED and Test/Status LED
 +
 +
== Installation ==
 +
Arduino IDE 1.6.5 or newer is needed (I tried it on version 1.6.7).
 +
 +
# Go to "File -> Preferences" and in the field "Additional Boards Manager URLs" introduce http://digistump.com/package_digistump_index.json and click OK.
 +
# Then go to "Tools -> Boards -> Boards Manager" and in the box "Type" select “Contributed”.  Select the “Digistump AVR Boards” package and click the “Install” button.
 +
# If you are using GNU/Linux you might need to add the rules for the USB programming device.
 +
# Now you can select the board for developing from "Tools -> Boards", most probably the device you have is “Digispark (Default - 16.5mhz)”.
 +
 +
=== Linux Rules ===
 +
 +
If you are running GNU/Linux and getting errors on upload or other strange results you might need to add the USB device to udev. You must place the udev rules below into a file named /etc/udev/rules.d/49-micronucleus.rules
 +
 +
Create the /etc/udev/rules.d/49-micronucleus.rules files with this content (setting up the correct permissions for user and group if desired):
 +
<pre>
 +
# UDEV Rules for Micronucleus boards including the Digispark.
 +
# This file must be placed at:
 +
#
 +
# /etc/udev/rules.d/49-micronucleus.rules    (preferred location)
 +
#  or
 +
# /lib/udev/rules.d/49-micronucleus.rules    (req'd on some broken systems)
 +
#
 +
# After this file is copied, physically unplug and reconnect the board.
 +
#
 +
SUBSYSTEMS=="usb", ATTRS{idVendor}=="16d0", ATTRS{idProduct}=="0753", MODE:="0666"
 +
KERNEL=="ttyACM*", ATTRS{idVendor}=="16d0", ATTRS{idProduct}=="0753", MODE:="0666", ENV{ID_MM_DEVICE_IGNORE}="1"
 +
#
 +
# If you share your linux system with other users, or just don't like the
 +
# idea of write permission for everybody, you can replace MODE:="0666" with
 +
# OWNER:="yourusername" to create the device owned by you, or with
 +
# GROUP:="somegroupname" and mange access using standard unix groups.
 +
</pre>
 +
 +
Then restart the system or run this command to apply the rules:
 +
<pre>
 +
udevadm control --reload-rules
 +
</pre>

Revision as of 10:58, 3 January 2016

The Digispark is an Attiny85 based microcontroller development board similar to the Arduino line, perfect for when an Arduino is too big. The

Specification

  • Attiny85
  • Power via USB or External Source (regulated 5v or 7-35v, 12v or less recommended with automatic selection)
  • On-board 500ma 5V Regulator
  • Built-in USB
  • 6 I/O Pins (2 are used for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming via USB)
  • 8k Flash Memory (about 6k after bootloader)
  • I2C and SPI (vis USI)
  • PWM on 3 pins (more possible with Software PWM)
  • ADC on 4 pins
  • Power LED and Test/Status LED

Installation

Arduino IDE 1.6.5 or newer is needed (I tried it on version 1.6.7).

  1. Go to "File -> Preferences" and in the field "Additional Boards Manager URLs" introduce http://digistump.com/package_digistump_index.json and click OK.
  2. Then go to "Tools -> Boards -> Boards Manager" and in the box "Type" select “Contributed”. Select the “Digistump AVR Boards” package and click the “Install” button.
  3. If you are using GNU/Linux you might need to add the rules for the USB programming device.
  4. Now you can select the board for developing from "Tools -> Boards", most probably the device you have is “Digispark (Default - 16.5mhz)”.

Linux Rules

If you are running GNU/Linux and getting errors on upload or other strange results you might need to add the USB device to udev. You must place the udev rules below into a file named /etc/udev/rules.d/49-micronucleus.rules

Create the /etc/udev/rules.d/49-micronucleus.rules files with this content (setting up the correct permissions for user and group if desired):

# UDEV Rules for Micronucleus boards including the Digispark.
# This file must be placed at:
#
# /etc/udev/rules.d/49-micronucleus.rules    (preferred location)
#   or
# /lib/udev/rules.d/49-micronucleus.rules    (req'd on some broken systems)
#
# After this file is copied, physically unplug and reconnect the board.
#
SUBSYSTEMS=="usb", ATTRS{idVendor}=="16d0", ATTRS{idProduct}=="0753", MODE:="0666"
KERNEL=="ttyACM*", ATTRS{idVendor}=="16d0", ATTRS{idProduct}=="0753", MODE:="0666", ENV{ID_MM_DEVICE_IGNORE}="1"
#
# If you share your linux system with other users, or just don't like the
# idea of write permission for everybody, you can replace MODE:="0666" with
# OWNER:="yourusername" to create the device owned by you, or with
# GROUP:="somegroupname" and mange access using standard unix groups.

Then restart the system or run this command to apply the rules:

udevadm control --reload-rules